How to Open S10 Hood With Broken Cable

If no then l. However if the handle inside broke then you just need to grab the cable with a set of pliers and pull it and that will release the hood latch.

How To Replace Hood Release Cable 00 07 Youtube

If the cable is broke inside at the handle you will have to remove the kick panel strip the coating back on the cable and pull the cable with a pair of pliers it should release.

. If the cable is broken under the hood you will need to remove the grill and use a screw driver to release the latch. Use a very long pair of needle nosed pliers and a flashlight. You have to disconnect the hood cable from where u usually would pull and disconnect it from their and just leave the wire out and just whenever u need to open it.

I need to open the hood of a 2000 S10 but the cable is broken off from the release lever inside the vehicle. The cable that opens the hood from the inside snapped on my 1991 chevy s10 this is how you open it from the outside. Locate either the cable and pull it if it broke inside the cab or if the hood is locked twist the safety lever under the hood in the direction the cable would normally pull it to release.

Take a thin phillips screwdriver put some tape on it and grab a flashlight then to where the latch is and you should be able to see where the cable connects put the end of the screwdriver where the cable pulls on then give it one good. Remove the clips that retain the hood release cable. Use a coat hanger or similiar tool to catch the release cables and trigger the cable.

The best way to open the hood is to have someone push down on it while you are pulling the cable. In order to aid in installation tie a mechanics wire to the end of the cable. Disconnect the hood latch cable from the primary latch assembly.

When you think that you have it apply some downward pressure to the top of the hood. If its broken further down you can take a flashlight to the front grille and peek through to see where the cable goes into the latch. Use a flat-bladed tool in order to release the clip and lift the cable assembly from the primary latch.

There is normally a 12 inch loop at the end of the releae. Basically you have to poke around until you are able to pop the hood. I cannot get the hood of my 2000 s10 Chev Blazer open.

Have a helper jiggle the hood up and down as you move the handle. Most of the time its just a matter of muscling it. Please let us know what questions you.

Depending on where it is broken if its broken at the handle you can try a pair of vice grips on the cable where the handle would go on. The inside hood lever works without unusual tension on cable but latch under hood will not release for main latch. Take a long screwdriver to try to pry the latch back just as the.

If that doesnt work using a flashlight locate where the cable attaches to the linkage. I have hard plastic levers look like small pry bars that I sometimes use on a stubborn hood. Hello all this is a quick video to show you how to work the latch mechanism if your hood release cable is either detached or brokenGM A-Body Models1982 -.

Then pull steadily on your wire. I attached a couple pictures below that will help with creating a metal rod to grab the latch. How do I - Answered by a verified Chevy Mechanic.

Sometimes they get stuck. This will compress the latch spring and hopefully take some pressure off of the mechanism so that it opens easily. Make sure it is releasing it.

If that opens the hood make sure to lubericate the linkage and the cable to prevent it from happening again. There should be a spring lever in the indent next to the headlight. Have you ever had a vehicle with a broken hood latch.

Locate the release catches for your hood. If need be then you will have to lay down under the front of the vehicle and reach up in there with a screwdriver and activate the latch where the cable goes. Look on the sides of your headlights for a slight indent behind the headlight.

Broken hood release cable on 93 Chevy S10. Pry open the clips with a flat-bladed tool. Generally you loosen the 4 bolts a little and persuade the hood into the best position.

1991 Chevy S-10 - Hood release cable has broken.

Why The Chevy Hood Release Handle Breaks And How To Sidestep The Issue

How To Replace Hood Latch Cable 1994 2004 Chevy S 10 Youtube

Broken Hood Latch Cable How Do I Open My Hood Now Potentially Easy Fix Ford Truck Van Specific Youtube